Billi Quadra

Choose a dispenser from our standard XL Levered, the innovative XT Touch version which has no levers and a clean style with all operation via a touchpad at the top of the tap or the XR Remote which has a separate control pad that can be mounted nearby the tap for greater design flexibility. All versions are available with the complete Boiling and Chilled range.

If the dispenser is to be mounted away from a sink, choose our XI Font. The ultimate in modern clean styling, it can be either surface mounted or recessed into the benchtop for a completely flush mounting.

The font comes complete with a 120mm dispenser riser to ensure sufficient clearance for a 250mm dispense height.

Within it's boiling and chilling cycle the Quadra systems may emit a small quantity of water through a 3mm pipe into the waste. This is quite normal and over the course of a day equates to a volume of approximately one toilet flush. The energy savings of the Billi system far outweigh any water cost.

Absolutely. In fact your dispenser can be installed up to 2.0m from its under counter water filter. Remember, there may be a boiling water delay with a long extension.

The Quadra range is water-cooled, and therefore does not rely on ventilation grilles to keep cool.

Billi quotes an initial cup delivery rate, which is the better measure for sizing a system than the hourly cup rates. Take as an example the Quadra 460XL. This has an immediate dispense capacity of 60 cups which means that if 60 people stood in a queue to get their hot drink, number sixty would receive theirs at the same temperature as number one.

All Billi units are designed to fit into standard cabinetry and under standard countertops. The Quadra Compact as an example measures 340 x 315 x 365 (H x W x D mm)

Most of the UK suffers from hard water, and in some areas this can even vary according to which reservoir the water is coming from. Any brand of boiling and chilled unit will very quickly scale up if a limescale filter is not fitted, and a failure attributable to scale is not normally covered by warranty.

This is a surface mounted drainage facility which fits into a worktop where there is a requirement to keep the boiling and chilled tap apart from a standard sink tap. It connects into the standard waste pipe.

By default, the Billi taps come with an electronic safety lock, which means that the boiling side of the tap cannot be operated by mistake. It requires the user to deliberately touch a padlock icon before boiling can be dispensed. Chilled water is always available and is never locked.

Yes, with the standard XL tap the levers can be raised to allow constant dispense, for refilling a jug for example.

Yes. We supply a 120mm riser as standard with a drainage font, and an option of 70mm riser. This gives a dispense height of 250mm and 200mm respectively.

Yes. We have a 36 month rental scheme which includes all servicing. At the end of three years, just take out a brand-new updated machine on a new contract or return the old unit to us.

This is the most accurate measure of a boiling and chilled taps capability. Simply it means that this is the number of cups that a boiling or chilled unit will dispense without any change in temperature. In the Quadra 4100XL, for example, the ICD is 100. If you had the situation of 100 staff members standing in a queue and drawing off their hot drinks, one after the other, after the other, the temperature for number 100 will be the same as number 1. Make sure when checking specifications of Billi or other brands, that you insist on knowing this figure. Whilst the hourly dispense is still important, it can be misleading because it is an average and doesn't account for peak times within that hour.

The tap will stop dispensing for a very short time. Billi have designed their system to ensure water is dispensed only at the correct temperature. As soon as enough water (2 cup fulls by volume) is heated, the unit will restart dispensing.

This is a stainless steel drip tray that is inset into a worktop to allow the boiling and chilled tap to be apart from the sink. It has its own connection to the waste and is often chosen for safety reasons. With each font is a riser of 70mm which lifts the tap high enough to dispense into a tall glass or jug. it is optional, although some clients choose to situate the tap so it can dispense over an existing sink. Clickhere for a picture of the standard XI font and XL tap.

The Billi system occasionally will flush a small amount of warm water through this hose to keep the system at a steady operating temperature. This is quite normal, as with any boiler, and the volume of water emitted is very low.

You can buy directly from us via proforma if you do not have a credit account. Call the sales line on 020 7456 6789 to get your quote. If you have a preferred merchants, please let us know and we will negotiate the same deal for you.